Sign in

Cryo Sample Holder Drawer with 13 electrical Contacts

Product code: RECOMCREC13V2

Featuring 13 electrical contacts this design allows for wiring up devices on flag style holders. Applications include also direct measurement of the sample temperature and/or resistive heating.
This particular model is optimized for cryogenic applications.
The receiver is equipped with a lever mechanism, pressing the sample plate down onto the cold  surface. Locking is engaged by approximately a full turn using the pincer or grabber on a wobblestick. By tightening the screw, the lever presses to both sides of the sample plate, forcing it down.
An improved  thermal contact to the cooling surface is thus achieved. The temperature difference between the sample holder and the receiver is approximately 2 Kelvin.

Please contact us for a detailed discussion of your requirements.

Specifications: Cryo Sample Holder Drawer with 13 electrical Contacts

Specifications:

  • Number of electrical contacts: 13
  • Materials:
    • Housing and shield caps: CuBe2 and copper Cu-OFE, gold plated
    • Positioning spheres: ruby
    • Isolators: PEEK
    • Contacts: CuBe2, gold plated
    • locking screw: Titanium grade 2
    • Screws: molybdenum
  • Contacts are glued with Epotek H20 and H70 UHV-compatible epoxy.
  • Temperature range: ~10K to 500K (lowest achievable temperature depends on the cryo-setup and thermal shielding)
  • Accepts SHOMEC13(MO) and SHOMEC13(MO-DT) flag style sample plate assemblies as well as all common flag style plates with no electrical contacts.
  • dielectric strength between adjacent contacts: 1000V. NOTE: Voltage resistivity depends on cabling and wire type.
  • Bespoken set of cables is not included - factory wiring with a preconfigured set of cables is mandatory.

Loading/unloading the sample and operation of the locking screw requires a WMG40 dual shaft wobblestick with PGWMS(OM) pincer for flag style plates or  a WM40 single shaft wobblestick with GRABSHOM end effector.

Downloads: drawing (pdf & 3D)  |  manuals

Options and Accessories

List price:

990.00 CHF

1'097.73 EUR*
1'306.74 USD*

Set of 13 coaxial cables, length = 1m, white, OD=0.8mm, PFA (TeflonĀ®), unterminated

Product code: IVWCOAXEC13UNT1000

Set of in-vacuum 50 Ohm coaxial cables, wired to RECOMEC13. The Cables are connceted to the sample receiver's electrical contacts with conductive Epoxy Epotek H20. Standard length is 1.0 meter. The other end of the cable is unterminated.


List price:

820.00 CHF

909.23 EUR*
1'082.35 USD*

DB15 female in-vacuum connector for RECOMCREC13 including assembly

Product code: UPGRADERECOMCREC13(+DB15F)


List price:

590.00 CHF

654.20 EUR*
778.76 USD*

Electrical Feedthrough DN40CF, D-Sub 15 Pin, Male

Product code: EFCF40DSUB15

Standard Sub-D Feedthrough, male, Allectra  / 210-D15-C40.

IMPORTANT: Vacuum-side mating connector must be Allectra / 211-FS15-PK DB15-small-size socket connector, Ferrovac Product IVWDB15FA, Ferrovac Part 64981.


List price:

1'700.00 CHF

1'884.99 EUR*
2'243.90 USD*

Sample Holder out of Molybdenum with 13 Electrical Contacts

Product code: SHOMEC13(MO)

Flag style sample holder with 13 electrical spring contacts and three slits for kinematic snap-in. Compatible with standard sample transfer systems for flag style holders. This product requires a RECOMEC13 sample receptor assembly.

Materials: Molybdenum, Beryllium-Copper, Stainless Steel. Isolators: shapal M


List price:

2'300.00 CHF

2'550.28 EUR*
3'035.86 USD*

Sample Holder 13 Electrical Contacts Molybdenum including temperature sensor

Product code: SHOMEC13(MO-DT)

Flag style sample holder with 13 electrical spring contacts and three slits for kinematic snap-in. With pre-installed lake shore DT-670 silicone diode temperature sensor.


Ferrovac AG | Thurgauerstrasse 72 | CH-8050 Zürich | www.ferrovac.com | link? | TEL +41 44 273 16 38 | FAX +41 44 273 16 30
© Ferrovac AG 2026 | © vogy GmbH 2026